Just how do you actually feel about How to Install a Bathtub?
Setting up a tub isn't precisely rocket science, but it does need solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently accessible, the task can relocate speedily; if you have to open up a wall surface to get rid of the old bathtub as well as position the new bathtub, the task is much harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old tub as well as embeded in the brand-new one. Make certain you have qualified yourself for the job as well as fit trying it. Instead of employing a specialist to take over a halfway-completed job, it is better to consider using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This short article will aid you mount a brand-new bath tub in your restroom if you have actually currently gotten a new bathtub and also don't need to transform the plan of your previous water supply pipes.
Your tools as well as product checklist ought to consist of the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, activate the taps to drain any type of water remaining in the system. The procedure of eliminating the existing taps can be rather problematic as a result of the restricted accessibility that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will originate from the pipelines. When the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Before going on to fit the new faucets, contrast the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin ensuring that the washing machines remain in area in between the tap as well as the sink. Protect the faucet in place with the supplier given backnut. As soon as the tap is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal tap connectors. The former kind needs to be attached to the faucet finishes initially, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Tub
Utilizing both wood boards under its feet, position the bathtub in the needed placement. The wood boards are practical in evenly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next goal is to make certain that the bathtub is leveled all round. This can be attained by checking the level and changing the feet on the bath tub until the level reads level.
To set up faucets, fit all-time low of the furthest flexible tap connector to the ideal supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Switch on the water system and also examine all joints and new pipework for leaks and tighten them if essential. Load the bathtub and additionally inspect the overflow electrical outlet and the normal outlet for leaks.
Finally, fix the bath paneling as explained in the maker's instruction manual. Tiling and also sealing around the bath tub should wait until the bathtub has been utilized a minimum of when as this will certainly resolve it into its last position.
Preparing for the Setup
To start with, the sustaining frame provided with the bath should be fitted (if called for) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the faucet features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you utilize every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last position.
Tiling Around the Tub
In the location where the bathroom satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall in between the bathroom and also the tiling, leading to complications with dampness and also feasible leakages to the ceiling below.
You can select from a range of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to allow for the activity experienced when the tub remains in usage. The sealant can fracture relatively early if you do not think about this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally easily offered on the market. It is recommended to fit the floor tiles using water-resistant or water-proof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that report on How to Install a Bathtub through an acquaintance on a different site. Do you know about another person who is involved in the niche? Be sure promote it. I value reading our article about Installing A Bathtub.
Services